Pointer mode
On this page
About pointer mode
In pointer mode, you aim the device at the computer screen. The pointer moves as you aim. The gyroscope of the device measures each turn of your hand. You click and scroll with large buttons on the screen of the device.
Use pointer mode when you are away from the computer: for a presentation, or for a computer that shows its screen on a TV. For work at a desk, touchpad mode is usually easier.
To open pointer mode, tap the mode button
in the toolbar. Then tap Pointer
.
The screen
The Standard layout has six controls:
- Hold to freeze, at the top. See Hold to freeze.
- Left and Right, the two large buttons in the center.
- Middle, below them.
- A vertical Scroll strip, on the right edge.
- A horizontal Scroll strip, along the bottom edge.
You can move, resize and hide each control, and add keys. See Edit the layout.
The toolbar
The toolbar shows icons. The table gives the name that VoiceOver speaks for each icon.
| Control | What it does |
|---|---|
| Stops the connection. The app then shows the server list. | |
| Shows the quality of the connection. Tap it to see the details of the server and the connection. See Connection state. | |
| Opens Pointer Layouts. See Save, load and reset layouts. | |
| Calibrate aim (target icon) | Starts the calibration. See Absolute pointing and calibration. |
| Opens and closes the layout editor. | |
| Opens or closes the keyboard. See Type on the computer. | |
| Opens the settings on the Pointer page. | |
| Changes the mode. | |
| Hides the toolbar. To show it again, tap the tab in the top right corner (Show toolbar). |
When the screen is narrow, Layouts
, Calibrate Aim, Edit Layout
and Settings
move into the More controls
menu. This is usual on an iPhone. Keyboard
stays on the toolbar. While the layout editor is open, Edit layout
is on the toolbar in place of Keyboard
.
The controls do not move when the toolbar hides or shows again.
Aim the device
Hold the device as you hold a remote control. Point its top edge at the computer screen.
- Turn the device left or right: the pointer moves left or right.
- Tilt the top edge up or down: the pointer moves up or down.
- If you turn the device around its long axis, the pointer does not move.
You can hold the device with the screen up, or on its side. The app measures how you hold the device. Thus a tilt up always moves the pointer up.
If you point the device almost straight up or straight down, the pointer moves more slowly and then stops. To prevent this, hold the device nearer to level.
The app reads the gyroscope only while pointer mode is on the screen. When the app goes to the background, the pointer stops.
Controls and gestures
| Gesture | Result on the computer |
|---|---|
| Turn or tilt the device | The pointer moves. |
| Touch and hold Left | The left button stays pressed until you lift the finger. A short tap is a left click. |
| Touch and hold Right | The right button stays pressed until you lift the finger. A short tap is a right click. |
| Touch and hold Middle | The middle button stays pressed until you lift the finger. A short tap is a middle click. |
| Hold Left and turn the device | Drag. |
| Move a finger up or down in the vertical Scroll strip | Vertical scroll. |
| Move a finger left or right in the horizontal Scroll strip | Horizontal scroll. |
| Touch and hold Hold to freeze | The pointer stops. It moves again when you lift the finger. |
| Touch and hold a custom key | The keys of the custom key stay pressed until you lift the finger. See Modifier keys and custom keys. |
To double-click, tap Left two times quickly.
The Scrolling setting changes how the strips scroll. See Scroll in steps or continuously.
To change the speed of the pointer, change Horizontal Sensitivity and Vertical Sensitivity. See Pointer settings.
Hold to freeze
While you touch and hold Hold to freeze, the pointer does not move. The area shows Frozen. When you lift the finger, the pointer moves again from the same position.
Use it in the same way that you lift a mouse from the desk:
- Touch and hold Hold to freeze.
- Turn your hand back to a comfortable position.
- Lift the finger.
- Aim again from the new position.
The pointer ignores the turns that you make while it is frozen.
A steady pointer
When you hold your hand still, it shakes a little. Without a filter, the pointer shakes with it. Stabilization removes this shake.
- When your hand is almost still, the filter is strong. The pointer stays still.
- When you move the device to aim at a new point, the filter becomes weaker. The pointer follows quickly.
- The filter does not remove movement. The pointer gets to the point where you aim, but a short time later.
Stabilization is on the Pointer settings page. The range is Off (0) to 10. The default is 10.
- A higher value makes the pointer more stable. But the pointer then follows a slow hand more slowly.
- A lower value makes the pointer follow your hand faster, but the pointer shakes more.
- Off removes the filter.
Hold the pointer when you click
When a finger touches a button, the device also moves a little. Thus, when a finger touches or leaves a control, the pointer stays at its position for a short time. The click goes to the point where you aimed, not to the point where the tap pushed the device. The app keeps the turn that you make during this time. The pointer moves after the hold.
Click Hold on the Pointer settings page sets this time. The range is Off (0) to 500 ms. The default is 150 ms. Click Hold also works when Stabilization is off.
- If a click goes to the wrong point, make the time longer.
- If the pointer starts a drag too late, make the time shorter.
Absolute pointing and calibration
With Absolute Pointing on, the pointer goes to the point on the screen that you aim at. For an accurate result, calibrate the aim from the place where you sit. The calibration measures how far you turn the device from one corner of the screen to the other.
Calibrate the aim
- Sit where you will use pointer mode.
- Tap Calibrate aim (target icon) in the toolbar. On a narrow screen, tap More controls
, then tap Calibrate Aim. - The app shows Corner 1 of 4. The pointer on the computer goes to the top left corner.
- Aim at the top left corner of the computer screen.
- Hold the device still. Then tap Mark Corner.
- Do steps 4 and 5 again for the top right corner, the bottom right corner and the bottom left corner. The app tells you which corner is next.
After you mark the fourth corner, the app turns on Absolute Pointing. It also sets Horizontal Sensitivity and Vertical Sensitivity for absolute pointing. The pointer is at the bottom left corner, where you aim.
During the calibration, the app hides the mouse buttons and the toolbar. This prevents an accidental click. To stop the calibration, tap Cancel. The settings then do not change.
If the corners are too near each other, or not in the correct order, the app shows "The corners were too close together, or out of order. Start again at the top left corner." Start again at Corner 1 of 4.
The app keeps Absolute Pointing and its calibration for each server. If you sit in a different place, or if you use a different screen, calibrate again.
Type on the computer
Pointer mode has a keyboard. The text that you type goes to the computer. The app does not keep it.
- Aim at the text field on the computer. Then tap Left.
- Tap Keyboard
in the toolbar. - Type on the keyboard of the device.
- To close the keyboard, tap Keyboard
again, or use the key that closes the iOS keyboard.
A row above the keyboard has Esc, Tab and the four arrow keys.
While the keyboard is open, the controls become shorter and stay above it. Thus you can aim and click while you type. The toolbar does not hide.
The keyboard closes when you open the layout editor or start the calibration. Each letter goes to the computer in the same way as in touchpad mode. See Type on the computer in touchpad mode.
Modifier keys and custom keys
Pointer mode has no modifier row. To press Ctrl, Shift, Alt or a different key, add a custom key to the layout.
A custom key keeps its keys pressed while you touch it. When you lift the finger, it releases the keys. For example, a custom key with Ctrl works as a Ctrl key. To send Ctrl+click, hold the custom key and tap Left. A custom key with Ctrl and C sends Ctrl+C.
A stage of a custom key can have more than one action. The key then presses the keys of each action at the time that the Wait slider sets. All these keys stay pressed until you lift the finger. If you lift the finger during a wait, the app cancels the actions that did not start. See Wait between actions.
A custom key can have more than one stage. Each touch then sends the next stage. The key editor is the same as the button editor in pencil mode. See The button editor.
The server changes each modifier to the equivalent key of its operating system. For example, the Meta key is Command on macOS, the Win key on Windows and Super on Linux. Alt is Option on macOS.
Edit the layout
In the layout editor, you can move, resize and hide each control, and add, change and delete custom keys.
Open and close the editor
- Tap Edit layout
in the toolbar. On a narrow screen, tap More controls
, then tap Edit Layout
. The controls show on a blue grid. Add key
shows below Edit layout
. - Make the changes.
- Tap Edit layout
again. The app closes the editor and saves your changes.
If you edit the Standard layout, the app does not change it. It saves your changes as a new layout with the name Custom Layout. Then it uses the new layout. If that name is in use, the app adds a number. If you close the editor with no change, the app saves nothing.
If you edit a layout that you saved, the app saves your changes into it when you tap Edit layout
to close the editor. It keeps the version from before your changes. To go back to that version, tap Revert "name". See Save, load and reset layouts.
What you can do in the editor
| Action | How |
|---|---|
| Select a control | Tap it. The control then has a dashed border and a dot on each corner. Buttons show below it. |
| Clear the selection | Tap the grid. For a standard control, you can also tap it again. |
| Move a control | Drag the control. If the control is too small to grab, a move handle shows below it. Drag the handle. |
| Resize a control | Select the control. Drag a corner dot. |
| Hide or show a control | Select the control. Tap the eye button |
| Add a custom key | Tap Add key |
| Change a custom key | Select the key. Tap the pencil button below it, or tap the key again. The Edit Button sheet opens. |
| Change the corners of a custom key | Select the key. Move the Radius slider. At the maximum, the key is round. |
| Delete a custom key | Select the key. Tap the red cross button |
When you move or resize a control, it aligns with the edges of the other controls. Lines show the alignment. A control cannot go past the edge of the screen. Each control has a minimum size.
You cannot delete the six standard controls. You can only hide them.
Portrait and landscape
A pointer layout has a portrait arrangement and a landscape arrangement. The editor changes the arrangement for the current shape of the screen. When you add or delete a custom key, the change applies to the two arrangements. When you move or resize a control, the change applies only to the current arrangement.
On an iPhone, pointer mode is always in portrait. The landscape arrangement is for the iPad. See iPhone, iPad and orientation.
Save, load and reset layouts
Tap Layouts
in the toolbar. On a narrow screen, tap More controls
, then tap Layouts
. The Pointer Layouts sheet opens.
| Item | What it does |
|---|---|
| A layout row | Tap it to use that layout. A check mark shows the layout in use. |
| Standard | The layout that the app includes. It shows Built-in. You cannot rename or delete it. |
| Save As… | Saves the current layout with a new name. Type the name in Layout name. Then tap Save. |
| Revert "name" | Puts back the version of the layout in use from before your last edit. It goes back one step only. It does not change the name. It shows only when an earlier version is available. Before it puts back the version, the Revert changes alert asks you to confirm. |
| The menu on a row (circle with three dots) | Shows Rename and Delete for that layout. You can also swipe left on the row. |
| Done | Closes the sheet. |
Go back to the standard layout
- Tap Layouts
. - Tap Standard.
The app uses the standard layout again. The layouts that you saved stay in the list. To remove a layout, delete it.
iPhone, iPad and orientation
- Pointer mode works on the iPhone and on the iPad. You aim the full device. Thus an iPhone is easier to hold and aim with one hand.
- On an iPhone, pointer mode is always in portrait. It does not turn with the device.
- On an iPad, the system can ignore the portrait lock. The app then uses the landscape arrangement of the layout when the screen is wider than it is tall. This is also true in a window that you resize.
- On an iPhone, Layouts
, Calibrate Aim, Edit Layout
and Settings
are in the More controls
menu. On an iPad in full screen, they are on the toolbar. - While the layout editor or the Pointer Layouts sheet is open, the toolbar does not hide automatically. For the defaults, see Auto-Hide in General settings.
Scroll in steps or continuously
A mouse wheel turns in notches. Each notch moves the page by a fixed distance. Some wheels and all laptop touchpads move the page smoothly. Scrolling on the Pointer settings page selects which of the two the computer does when you move a finger in a Scroll strip.
- Step by Step (the default): the page moves one notch at a time, as with a mouse wheel. This works in all apps.
- Continuous: the page moves smoothly with your finger. Many apps can do this, for example web browsers. Some apps move one full notch for each small movement. In these apps, the page scrolls too far. If this occurs, select Step by Step.
On Windows, a window that runs as administrator always uses Step by Step scrolling, also when you select Continuous.
This setting is only for pointer mode. Touchpad mode does not use it.
Pointer settings
Tap Settings
in the toolbar. The Pointer page opens.
| Setting | What it does | Default |
|---|---|---|
| Absolute Pointing | On: the pointer goes where you aim the device. Off: each turn moves the pointer by a distance, as with a mouse. A calibration turns it on. The app keeps a value for each server. | Off |
| Horizontal Sensitivity | Sets how far the pointer moves left and right for one turn. The range is 1 to 100. Absolute pointing has its own value. A calibration sets that value. The app keeps a value for each server. | 30 (absolute: 20) |
| Vertical Sensitivity | Sets how far the pointer moves up and down for one tilt. The range is 1 to 100. Absolute pointing has its own value. A calibration sets that value. The app keeps a value for each server. | 15 (absolute: 35) |
| Stabilization | Removes the shake of your hand. See A steady pointer. The value is the same for all servers. | 10 (range Off to 10) |
| Click Hold | Sets how long the pointer stays still when you touch a control. See Hold the pointer when you click. The value is the same for all servers. | 150 ms (range Off to 500 ms) |
| Scrolling | Sets how the Scroll strips scroll: one notch at a time, or smoothly. See Scroll in steps or continuously. The value is the same for all servers. | Step by Step |
| Invert Button Order | Puts the three mouse buttons of touchpad mode in the order Right, Middle, Left. It does not change pointer mode. To move the buttons of pointer mode, use the layout editor. The value is the same for all servers. | Off |
The page shows the two sensitivity sliders for the current mode. To see the values for the usual mode, turn off Absolute Pointing.
The app keeps Absolute Pointing, Horizontal Sensitivity and Vertical Sensitivity for each server. Thus you can change them only while the app is connected. Without a connection, the page shows them dimmed. See Settings for each server.
For Haptic Feedback, Auto-Hide and Hide Delay on the General page, see General settings.